staking out a freestanding deck

How to Build a Deck how-tos DIY

Pour Concrete. After mixing a batch of concrete, shovel it into the holes and lop off the excess using a spare wood stake (Image 1). Before allowing the concrete to cure for 48 hours, embed a J-bolt into each caisson (Image 2). Eventually, this will help tie down the deck.

Building Permits for Decks - St. Mary's County Government

on your property to identify the location of the deck construction. You will also be provided with. CAG #22 and an inspection application form. Please follow the CAG #22 instructions as they pertain to “staking and flagging the lot,” filling out the inspection application form and paying the applicable inspection fee. The fee and

How to Lay Out a Deck on Un-Level Ground Home Guides SF Gate

Measure down from the bottom of an exterior door or window and mark the side of the house at the height of the finished deck with a marking crayon. If the deck is free-standing and doesn't attach to a house, drive a 48-inch wood stake several inches into the ground with a steel mallet and mark the height for top of the deck

How to Layout a Perfect Rectangle for Deck or Patio ? DIY Projects

Jul 6, 2017 View this quick video tip demonstrating how to make perfectly square angles when laying out a deck, patio or other large rectangular shapes. First, stake the location where you want the 90-degree angle and attach two string lines. Attach one of the two lines to a second stake, where you want the first side

How to start a deck (laying out your post and digging) - YouTube

Jun 29, 2013 Luke shows how to lay out your deck using a CAD design and the back of the house. Questions:

Building a Freestanding Deck in a Seismic Zone Professional Deck

Aug 7, 2017 To properly locate the footings on a sloped site like this, we like to stake up 2x4s to create a mock footprint of the deck. This simplifies the layout process, and the 2x4s also double as batter boards from which we plumb down to establish finish deck and footing placement. The freestanding deck is located on

Deck Layout and Footing Position Spacing DIY Deck Plans

To create a square corner in your deck outline, use the “rule of 3,4,5”. Measure from the corner stake along one angle of your corner to 3 feet. Measure from the post along the opposite angle to 4 feet. Mark both points and measure between them diagonally. The distance should be 5 feet. Adjust your second angle in or out

How to Lay Out a Deck - Better Homes and Gardens

Expect to spend four to five hours building batterboards, figuring out the layout, stretching lines, and determining footing locations. To lay out the deck, you need to be able to measure and check for square, fasten screws, and pound stakes. It's also a good Drive a stake or landscape spike into the ground to mark the spot.

How to Frame a Multi Level Deck

Step 1 - Stake out Frame. The first step is to stake out the perimeter of your deck. Insert a stake at the corners of the deck and every 10 feet in between. Start with the lower level of the deck and then move to the upper level.

Deck layout procedure after the ledger board is attached

How to lay out the deck:once the the ledger board installed against the building that board forms the home-base from which all other deck measurements are made. done the level, plumb and square-up of the deck from the ledger board (building attached decks & porches) or from batter boards (for a free-standing deck ).

Tent "Platforms", "Pads", and Staking on Same [Archive] - WhiteBlaze

I know that a tent "platform" is a small deck, usually made of wood, which is raised up off the ground, and you set your tent up on it. On the other hand, judging from the pictures I found in a Google search, a tent "pad" is simply a flat area of the ground which is designated as a campsite and which often

Freestanding deck right next to house This Old House

Jul 30, 2014 I'm planning out a deck that's about a 16 by 10 foot rectangle. (I'll be angling off one corner of it but that's not important for the question.) I want it to be next to the house, but our house is old and a bit of a hassle from a surface standpoint - it's basically 90 year old wood siding with 3 coat stucco over it.

DIY Build a Freestanding Cantilevered Deck - Extreme How To

Aug 25, 2010 How to Build a Freestanding Cantilevered Deck. Unless I was to tear out the ceiling, I wouldn't be able to add nuts and washers to through-bolts on the interior side of the rim joist. And, if I couldn't I then ran two new rows of string within the perimeter, staking the location of each support post. I used a

How to Build a 12 X 12 Freestanding Deck Hunker

Dec 4, 2011 As the word implies, a freestanding deck is sometimes referred to as a floating deck and is not attached to any permanent structure. Whether you are building this type of deck because the corners for the deck at the desired location. Use a tape measure and hammer a stake into the ground at each corner.

How to Build a Floating Deck - The

Measure out the space in your yard or sketch out the design of your deck, making notations regarding it's length, depth, width, and interior framework. I wanted our deck to have enough space for a dining set and lounge chairs, so I landed on a size of 10 ft. wide by 18 ft. long. Hammering a stake to mark area for a floating